AquaVantage 1990 GD
High performance for the precision end
Brulin's advanced GD-series chemistry for aerospace and OEM duties.
Four AquaVantage grades. Same substrate safety across all of them — the difference is the duty.
Degrease, free rinse, corrosion inhibitor
AquaVantage 1990 GD does three jobs in one bath, so a part can come out of the machine ready for the next operation instead of going through three tanks to get there.
Degrease
Lifts buffing compounds, coolants, fats, greases and the whole run of oils — cutting, drawing, forming, hydrocarbon, lubricants, water-soluble. Released oil separates out for skimming instead of emulsifying into the bath, so the tank lasts.
Data sheet: separates oil effectively for improved oil removalFree rinse
The surfactant and builder package is picked so it goes back into solution in the rinse water and sheets off the part, instead of beading up or drying to a film. That sheeting is what a water-break-free surface is.
It matters because of what comes next. Anything left on the surface is an adhesion defect in the paint, the bond, the plate or the coating, and it will not show up until that stage fails.
Data sheet: free rinsing — permits improved adhesionCorrosion inhibitor
Two different jobs, and it is worth keeping them apart. In the tank: the bath is alkaline, so steel sits in its passive range and holds a stable oxide, and the inhibitor package adsorbs a film on the surface. None of that follows the part out of the bath.
Out of the tank: a trace carries through the rinse and holds off flash rust for a short while — indoors and dry. It is a residual film, not a coating. For anything going on a shelf, follow it with a dedicated rust preventative.
Data sheet: in-process corrosion controlGetting the protection to survive the rinse
This is where most people lose it. A freshly cleaned part is the worst case there is — you have just taken off the oil film that was protecting it, and bare steel sitting wet in aerated water goes off in minutes. Four things decide whether it holds.
Three tanks become one. Less floor space, one bath to dose and monitor, one drum to buy, and no transfer between stages for the part to flash over in. Dose and temperature are on the dosage calculator →
High performance for the precision end
The GD series exists on a spectrum, and 1990 GD occupies the high-performance end: advanced aqueous cleaning for precision aerospace and OEM work, with the free-rinsing, oil-splitting behaviour the series is qualified on.
Its brand documentation is on file and its slot in the range is specification-driven — where 815 GD is the qualified default, 1990 GD answers the applications that ask for more, confirmed per specification in trial.
Talk to us with the spec in hand; matching the GD grade to the requirement is exactly the kind of decision the trial exists to settle.
Where it earns its keep
Precision aerospace cleaning duties across OEM and MRO work.
Dose: 3–15% (typ. 5%; 5% minimum on aluminium). The trial sets your exact process values; the TDS governs.
The working process
Right product, right job
1990 — high performance
Specification-driven precision duties.
AquaVantage 815 GD
The qualified default
View →Delivered within Australia. Outside Australia, request a delivered price.
Anti-RustStops flash rust on cleaned steelView & buy →
| Mild & carbon steel | Safe in prescribed use |
| Stainless steel | Safe in prescribed use |
| Cast iron | Safe in prescribed use |
| Aluminium & titanium | Aerospace-approved multi-metal duty — aluminium and titanium on the TDS list |
| Magnesium & soft alloys | Magnesium and its alloys on the TDS list |
| Zinc & galvanised | Not on the TDS list — test first |
| Copper & brass | Copper alloys and plating on the TDS list |
| Plated finishes (Cd·Cr·Ni) | Cadmium, chrome and nickel plating all on the TDS list |
| Plastics & rubbers | Acrylics · HDPE · nitrile · PVC · rubber on the TDS list |
| Painted / coated surfaces | Painted surfaces on the TDS list |
| Transport | Not classified as Dangerous Goods for transport |
This is not a single-use chemical
A common misconception treats industrial chemistry like dishwater — used once, tipped out. A defended bath of AquaVantage 1990 GD works for weeks of production: the oil-splitting formulation sends released oils to the weir, solids leave through the filter, and the chemistry keeps working until genuine depletion.
Change out on evidence, not anxiety: when cycle times stretch or results fade at correct concentration, the bath has earned its retirement. Top-ups at specification carry it between changes.
- Skim or weir oils continuously — oil load is bath killer #1
- Filter solids; drain settled sludge from the sump
- Verify concentration on schedule — titration method on the product TDS
- Log it — the trend predicts top-ups before cleaning fades
Drum and bath, both looked after
- Precautions for safe handling Before use carefully read the product label.
- Use of safe work practices are recommended to avoid eye or skin contact and inhalation.
- Observe good personal hygiene, including washing hands before eating.
- Prohibit eating, drinking and smoking in contaminated areas. 7.2 Conditions for safe storage, including any incompatibilities Store in a cool, dry, well ventilated area, removed from incompatible substances and foodstuffs.
- Ensure containers are adequately labelled, protected from physical damage and sealed when not in use.
- Check regularly for leaks or spills. 7.3 Specific end uses No information provided.
Lid the tank between shifts — holds temperature, limits evaporation, keeps dust out.
Idle periods: a warm, stagnant aqueous bath can support biological growth over extended stagnation. Circulate periodically, keep concentration at specification, never leave an open tank standing for weeks.
Extended shutdown: drain to sealed, labelled containers — or schedule changeover for restart day.
The icons on the label, and what they mean
These are the manufacturer’s own label marks, not third-party certifications. Where a named approval exists it is listed in full on this page. The compatibility table above is what governs.
The paperwork, on the page
Hazard identification
| H315 | Causes skin irritation. |
| H319 | Causes serious eye irritation. |
| P264 | Wash thoroughly after handling. |
| P280 | Wear protective gloves/protective clothing/eye protection/face protection. |
| P352 | IF ON SKIN: Wash with plenty of soap and water. |
| P338 | IF IN EYES: Rinse cautiously with water for several minutes. |
| P321 | Specific treatment is advised - see first aid instructions. |
| P313 | If skin or eye irritation occurs: Get medical advice/ attention. |
PPE & exposure controls
- Control parameters Exposure standards No exposure standards have been entered for this product.
- Biological limits No biological limit values have been entered for this product. 8.2 Exposure controls Engineering controls Avoid inhalation.
- Use in well ventilated areas.
- PPE Eye / Face Wear splash-proof goggles.
- Hands Wear PVC or rubber gloves.
- Body When using large quantities or where heavy contamination is likely, wear coveralls.
- Respiratory Not required under normal conditions of use.
First aid
- Description of first aid measures Eye If in eyes, hold eyelids apart and flush continuously with running water.
- Continue flushing until advised to stop by a Poisons Information Centre, a doctor, or for at least 15 minutes.
- Inhalation If inhaled, remove from contaminated area.
- Apply artificial respiration if not breathing.
- Skin If skin or hair contact occurs, remove contaminated clothing and flush skin and hair with running water.
- Continue flushing with water until advised to stop by a Poisons Information Centre or a doctor.
- Ingestion For advice, contact a Poisons Information Centre on 13 11 26 (Australia Wide) or a doctor (at once).
- If swallowed, do not induce vomiting.
- First aid facilities Eye wash facilities and normal washroom facilities should be available. 4.2 Most important symptoms and effects, both acute and delayed May cause irritation to the eyes, skin and respiratory system. 4.3 Immediate medical attention and special treatment needed Treat symptomatically.
Storage & handling
- Precautions for safe handling Before use carefully read the product label.
- Use of safe work practices are recommended to avoid eye or skin contact and inhalation.
- Observe good personal hygiene, including washing hands before eating.
- Prohibit eating, drinking and smoking in contaminated areas. 7.2 Conditions for safe storage, including any incompatibilities Store in a cool, dry, well ventilated area, removed from incompatible substances and foodstuffs.
- Ensure containers are adequately labelled, protected from physical damage and sealed when not in use.
- Check regularly for leaks or spills. 7.3 Specific end uses No information provided.
Disposal
- Waste treatment methods Waste disposal Reuse where possible.
- For small amounts, flush to sewer with excess water.
- Alternatively absorb with sand, vermiculite or similar and dispose of to an approved landfill site.
- Contact the manufacturer/supplier for additional information if disposing of large quantities (if required).
- Legislation Dispose of in accordance with relevant local legislation.
Transport & dangerous goods
- INFORMATION NOT CLASSIFIED AS A DANGEROUS GOOD BY THE CRITERIA OF THE ADG CODE, IMDG OR IATA LAND TRANSPORT (ADG) SEA TRANSPORT (IMDG / IMO) AIR TRANSPORT (IATA / ICAO) 14.1 UN Number None allocated.
- None allocated. 14.2 Proper None allocated.
- Shipping Name 14.3 Transport None allocated.
- None allocated. hazard class 14.4 Packing Group None allocated.
- None allocated. 14.5 Environmental hazards Not a Marine Pollutant. 14.6 Special precautions for user Hazchem code None allocated.
Asked at the tank
What dilution and temperature do I run?
When do I change the bath?
Can algae grow in the bath if it sits unused?
Can I get the SDS before buying?
See also: Ultrasonic degreaser: how to choose.
Not sure which chemical? See which chemical for which metal and soil.
Prove it on your parts
The trial pairs AquaVantage 1990 GD with your components — concentration, temperature and cycle documented before you order a drum. Wrong chemistry for your soil? The trial says so.
Approved and conformant — by name
AquaVantage 1990 GD carries one of the broadest approval sets in the Brulin range. If your process is governed by one of these specifications, the chemistry is already qualified for it.
- Airbus AIPI 09-01-003
- Airbus UK ABP 8-1290
- Boeing BAC 5763 Emulsion Cleaning
- Boeing HP 9-25 Degreasing
- Boeing D6-17487 Rev. K Exterior Cleaner
- Teledyne Ryan RACO 2833
- Rolls-Royce CSS204 Type A
- Rolls-Royce OMAT 1/24 AG
- Safran PR-1500 · DMP 13-300
- GE Aviation S-421
- GE Aviation CT-882 Solvent Replacement
- Lucas Aerospace DC Starter/Gen
- NASA — Cleaning for Oxygen Service
- Lockheed Martin EPS G32.0160 · LMA-PG006
- General Dynamics (Electric Boat)
- UTC Aerospace (Rohr) ML21345
- Honeywell EMS 53170 · Meggitt AP-842
- USDA A1 · SCAQMD Clean Air Solvent
- ARP 1755A (Cat. 9) · 1755B (Cat. 10)
- ASTM F-483 · F-484 · F-485 · F-502
- ASTM F-519 Hydrogen Embrittlement
- ASTM F-945 Ti Stress · F-1110 · F-1111
- NSN 6850-01-428-8842 · 6850-01-435-6459
- No cyanides · No sulfides
Source: Brulin Specification Conformance & Testing (750-042Z). Approvals are held by the manufacturer and apply to the product as supplied — confirm the current revision with Misonics before writing it into a process specification.
Filter bags for this bath
The bag is what keeps the bath working — it takes the soil out before it settles back onto the next load. This is a strong alkaline bath, and that rules the media in and out before micron rating comes into it.
Rated to pH 14. This is what it is for. Start at 25 µm unless something downstream needs finer.